Vintage Woodworks
Close this window
PL Premium Adhesive


PL Premium is a revolutionary new construction adhesive that provides superior results and is safe and easy to use. It may be used inside or outside and will last as long as the surface joins together. Because the bonding strength of PL Premium is so strong, much less adhesive is required to complete your projects. PL Premium is waterproof, paintable, and exhibits low odor.




Application:
  • Surface temperatures above 5 degrees C (40 degrees F) are
    recommended.
  • Surface must be completely dry, free of moisture, and clean.
  • PL Premium comes ready to use.
  • Do not open tubes until preparatory work has been completed.
  • Cut nozzle to desired size opening.
  • Place the tube in standard caulking gun and puncture the seal inside the
    nozzle.
  • Apply the adhesive with a steady pressure.
  • Bond and support the assembly until the adhesive has set. (12 hours)
  • Spray a mist of water in joints where thick cross sections are present to
    aide in cure.
  • PL Premium has low toxicity, non flammable/non combustible - very low odor, it is environmentally safer than any other conventional adhesive.
  • PL Premium works fast - up to three times faster than anything else on
    the market today and that means more productivity on the job.
  • PL Premium is so strong that it offers twice the coverage of conventional
    adhesives. It is also waterproof and useable in all climate extremes.
    Bonds can be made in temperatures ranging from - 18 degrees C
    (0 degrees F) to 204 degrees C (400 degrees F).


    SUPPORT IS REQUIRED UNTIL THE ADHESIVE HAS SET. SETTING TIME MAY VARY DEPENDING ON HUMIDITY AND TEMPERATURE DURING THE CURING PERIOD.

    Working Time:
    You can work with the adhesive for up to 45 minutes.

    Storage:
    After completion of your work, wrap the aluminum foil tightly around nozzle and seal it with a piece of scotch tape.

    Coverage:
    Each 10 ounce tube seals 24 lineal feet in a 1/4 X 1/4 joint.

    Curing Action:
    Cures by reacting with moisture. At higher levels of moisture, the cure rate will be faster. At lower moisture levels the cure rate will be slower.

    Curing Rate:
    A 1/4 inch bead cures in approximately 16 - 24 hours at 25 degrees C (78 degrees F) and 50% relative humidity. Cures even in cold temperatures.

    Clean up:
    Immediately after use, clean equipment with Acetone or Mineral spirits. Cured sealant can be removed by cutting with a sharp edged tool, thin films by abrading.

    Additional Features:
    Can be sanded and painted.

    Shelf Life:
    1 year in unopened tubes at 24 degrees C (75 degrees F), 50% relative humidity.

    For the BEST Performance:
  • Wear disposable gloves while using PL Premium or staining of the hands will occur because of moisture in the skin. Staining will disappear in about 3 days.
  • Be very careful not to allow PL Premium to cure on a finished surface. It is next to impossible to remove without sanding. Solvents have little effect on PL Premium once cured.
  • PL Premium does not bond well to certain plastics. Test a piece for adhesion.

    The information given and recommendations made herein are based on research and are believed to be accurate but no guarantee of their accuracy is made. In every case, before using any product in full scale production, we recommend you make your own test to determine if suitable for your particular purpose under your own operating conditions. Sold without warranty as to merchantability or fitness for a particular purpose or any other warranty, express or implied. No representative of ours has any authority to waive or change the foregoing provisions. Nothing contained herein shall be construed to imply the non-existence of any relevant patents or to constitute a permission, inducement or recommendation to practice any invention covered by any patent, without authority from the owner of the patent.

    Close this window